Deflate and Pack an Inflatable Paddle Board
A plain guide to releasing the air valve, drying and cleaning an inflatable paddle board, then rolling it into its bag for the trip home.
Contents
- Get the board out of the water clean
- Open the air release valve correctly
- Press the air out of the board
- Dry the board before rolling it
- Roll the board from nose to valve
- Fit the board into the roll-up bag
- Questions About Deflating a Paddle Board
- How do I deflate a stand up paddle board?
- Should I wash the board before I deflate it?
- What happens if I roll up a wet paddle board?
- Which end should I roll the board from?
- Do I need a special bag for a rolled paddle board?
Deflating and packing an inflatable paddle board takes a few careful steps: open the air release valve, let the air escape, dry and clean the board, then roll it from the nose toward the valve and slide it into its bag. Doing the steps in that order protects the board and makes the package easier to carry. The whole job goes faster when you rinse off sand and salt before the board dries.
- Press the valve pin in and twist it to lock the valve open so air escapes on its own.
- Let the board dry fully before rolling it, because trapped moisture can damage the material over time.
- Rinse off sand and salt water first, since grit left on the surface can rub into the board when rolled.
- Roll from the nose end toward the valve so escaping air has a clear path out.
- Use the roll-up bag and its straps to keep the packed board compact and protected in transit.
Get the board out of the water clean
Cleaning an inflatable paddle board starts before you deflate it, while the board is still firm and easy to handle. Rinse the deck pad, rails and bottom with fresh water to lift off salt and loose sand. A soft brush or a cloth lifts sand removal from the textured deck pad and the seams.
Sand trapped in the folded material can grind against the surface during transport and wear the coating. Tip the board on its edge and let the water run off before you set it down again. Wipe the fin area and the valve surround, since grit collects in those small recesses.
Keep the board out of direct sun while it drains, because heat softens the material and makes handling awkward. A shaded spot on the sand or a patch of grass works well for this stage. Move to deflation once the surface stops dripping.
Open the air release valve correctly
The air release valve sits at the tail of the board and controls how the air leaves. Remove the valve cap and press the pin in the center with your finger. Air escapes with a steady hiss once the pin is pressed.
Twist the pin a quarter turn to lock the valve in the open position for hands-free deflation. Locking the valve lets you press down on the board with both hands while the air drains. Do not force the pin if it feels stiff, since the cap thread may still be engaged.
Stand clear of the valve opening so the rushing air does not blow sand onto the board. Keep the cap in your pocket or in the bag so it does not get lost on the beach. The valve stays locked open until you are ready to roll.
Press the air out of the board
Once the valve is open, the board still holds air in its inner chambers and along the seams. Fold the board in half lengthwise and press down with your knees or hands to push that air toward the valve. Work from the nose end toward the tail in slow passes.
Repeat the folding and pressing until the board stops sighing and feels flat. A few extra passes push out the last pockets near the rails. Take your time here, because a flatter board rolls tighter and fits the bag more easily.
Keep the valve clear of the sand while you press, and check that the pin is still locked open. If air keeps hissing after several passes, look for a second chamber valve or a cap that is still closed. Close the valve pin only after the board is flat.
Dry the board before rolling it
Drying the board is the step that protects it for the next trip. Moisture trapped inside a rolled board can encourage mildew and weaken the coating over time. Wipe the surface with a dry towel and leave the board flat in the shade until it feels dry to the touch.
Pay attention to the deck pad, the seams and the valve area, since those spots hold water longer. Lift the board and check the underside as well. A dry board also weighs less and rolls without slipping.
Skip packing a wet board when you can, and let it finish drying at home before long storage. Air the bag out too, so dampness does not stay inside with the board. A dry bag keeps the next outing simple.
Roll the board from nose to valve
Rolling up the board works best starting at the nose and finishing at the valve. Lay the board flat with the deck pad facing up and fold in the side rails a little. A narrow fold keeps the roll straight and the edges even.
Roll firmly and slowly, pressing out air as you go, until you reach the valve. Keep the roll tight but avoid creasing the same line repeatedly. The valve ends up on the outside, where you can reach it later.
Secure the rolled board with the strap or band that came with it. A loose roll unfolds in the bag and takes more space than needed. Check that the fin and any accessories are packed separately and not crushed inside the roll.
Fit the board into the roll-up bag
A roll-up bag holds the packed board and a few small items, and its straps compress the load. Slide the rolled board into the bag with the valve end first or last, whichever sits flatter. Fasten the main closure and pull the compression straps snug.
The bag protects the board in transit and keeps sand and water off the inside of a vehicle. Place the pump, leash and fin in their own pockets so they do not press into the board. Leave the bag slightly open for airflow if the board might still be damp.
Carry the bag by its handle or shoulder strap rather than dragging it, and set it down gently. Storing the packed board flat or upright in a dry place helps it keep its shape. Check the valve cap is fitted before the bag goes into storage.
Questions About Deflating a Paddle Board
How do I deflate a stand up paddle board?
Deflating a stand up paddle board means opening the air release valve at the tail, pressing the pin and locking it open, then pressing the air out from the nose toward the valve. Rinse and dry the board first, then roll it from the nose toward the valve once it feels flat. Close the valve cap after rolling.
Should I wash the board before I deflate it?
Yes, rinse the board with fresh water and remove sand before deflation, while it is still firm. Sand and salt left on the surface can rub into the material when the board is rolled. Wipe the deck pad, rails, seams and valve area, then let the board dry.
What happens if I roll up a wet paddle board?
A wet board rolled and stored for a while can develop mildew and coating damage from trapped moisture. Dry the deck pad, seams and valve area with a towel and let the board air in the shade. If you must pack it damp, open the bag at home and let the board finish drying.
Which end should I roll the board from?
Roll the board from the nose toward the valve at the tail, so the last air escapes as you finish. Folding in the side rails first keeps the roll narrow and even. The valve then sits on the outside of the roll for easy access.
Do I need a special bag for a rolled paddle board?
A roll-up bag made for inflatable boards holds the rolled board and compresses it with straps. The bag keeps sand and water off the board and makes carrying easier. Pack the pump, fin and leash in separate pockets so they do not press into the board.